Makabit+

Makabit+ is a cold-processed, directly installab- le, single-component repair material. It can be processed directly from the container without the need for additives.
In order to ensure proper adhesion, the areas in need of repair must be free of “standing” water and other contaminants. For achieving optimal results, we recommend priming the subsurface with ESTOL C40B5-S. To support and accelerate the hardening process in dry weather, the material can be sprayed with water (approximately 0.5 l per 25 kg of mix) pri- or to compressing (32 x 25 kg of metal contai- ners available per pallet). Makabit+ can be ap- plied with a layer thickness of between 1 and 5 cm. Deeper segments can be filled with crushed stone or gravel or simply apply Makabit+ in mul- tiple layers.

Makabit+ is a cold-processed, directly installab- le, single-component repair material. It can be processed directly from the container without the need for additives. In order to ensure proper adhesion, the areas in need of repair must be free of “standing” water and other contaminants. For achieving optimal results, we recommend Makabit+ can be taken directly from the contai- ner and poured into the pothole, with a bit extra heaped on top. After this, first hammer down and then compress with a vibrating plate or stamper. The repaired area will immediately be ready for traffic once sand has been strewn across it. Nor- mal road traffic will provide the final compres- sion.

Makabit+ can be stored in its original container for up to 12 months – in a cool, dry place and not outdoors. The temperature range for installati- on is -20 to +40°C. For improved processing in winter temperatures, we recommend storing Ma- kabit+ in temperature-controlled areas between 10 and 15°C.

Makabit82 ® Super

Eliminates damage on all road surfaces:
Makabit® 82 Super 0/5 – Installation depth up to max. approx. 50 mm
Makabit® 82 Super 0/8 – Installation depth up to max. approx. 60 mm
Makabit® 82 Super 0/11 -Installation depth up to max. approx. 80 mm
Deeper damage areas can be evened out using Makabit 82 ® Super (and/or filled with loose chippings). Creating a new top layer, after raising and regulating shafts and gutter run-off, for example. Creating a new top layer for any digging work done on traffic surfaces.
Creating ramps and providing repairs to both industrial floorings (including concrete) as well as to courtyard and garage surfaces.

Makabit 82 ® Super is a high-quality cold mixture with fast-setting properties and unsurpassed adhesive strength.
Makabit 82 ® Super comes ready-to-use in a container (1-component) and can be used immediately. Processing can be performed independent of weather conditions, all year round as well as in frost temperatures.
Makabit 82 ® Super can be driven on immediately after compaction. After setting, Makabit 82 ® Super has the same stability of a hot asphalt and poured asphalt surface (see test report from the TU-Munich no: 50-11-0529). Deformation is no longer possible after setting, even at high temperatures during summer months.
Makabit 82 ® Super can be paved on with conventional hot mixture paving after a brief staying time. Makabit 82 ® Super is verifiably recyclable after installation (documented by the KIT test report).

Clean dry, damaged areas and pre-treat with ESTOL C40B5-S or ESTOL-Adhesion Primer. For optimum flank adhesion add a thin coat of ESTOL-Contact Adhesive.
Apply Makabit 82 ® Super generously to the surface and distribute evenly, then compact using a tamper, vibrating plate or roller.
Lightly sand the surface to reduce surface stickiness.
Open section for flowing traffic. … finished!

Makabit 82 ® Super is available in 25 kg or 40 kg containers. 32 containers with 25 kg are packed onto one pallet and 16 or 24 containers with 40 kg are packed onto one pallet. Makabit 82 ® Super is frost-tolerant (for better processing during winter months we nonetheless recommend storage at room temperature).
Store the container in a cool, dry place and do not expose to direct sunlight. Makabit 82 ® Super can be stored in its unopened original container for approx. one year. Opened containers should be closed and quickly used up.
We are happy to send you a free, no-obligation quote and our technical data sheets. These data sheets will provide you with more data and information about how our products are processed.

ESTOL – Biomak

Thanks to its optimised formula, ESTOL-Biomak can be used for all road surfaces, like stone mastic asphalt, poured asphalt and concrete for example.
ESTOL-Biomak is ideal for improving and compensating uneven areas as well as for repairing damage on thin pavement layers. ESTOL-Biomak is suitable for creating new surface layers after raising and regulating shafts and gutters.
ESTOL-Biomak 0/2 – Installation depth up to max. 10 mm
ESTOL-Biomak 0/4 -Installation depth up to max. 40 mm
ESTOL-Biomak 0/8 – Installation depth up to max. 60 mm
ESTOL–Biomak 0/11 – Installation depth up to max. 80 mm
Deeper damaged areas can be evened out using ESTOL-Biomak (and/or filled with loose chippings).

ESTOL-Biomak is a reactively hardening asphalt mixture with 0/2, 0/4, 0/8, and 0/11 chipping grain sizes.
ESTOL-Biomak can be cold processed with a high initial stability after approx. 15 minutes.
ESTOL-Biomak sets quickly when water is added, whereby the material also adheres well to moist surfaces.
BIOMAK is solvent-free (VOC acc. to H RepA). ESTOL-Biomak 0/2 can be spread extremely smooth. Deformation is no longer possible after setting, even at high temperatures during summer months.
ESTOL-Biomak can be easily paved on and can also be installed in frost temperatures (follow technical data sheet).
ESTOL-Biomak is made with renewable plant materials and is also recyclable making it environmentally friendly.

Clean surface from dust and standing water.
Apply a thin coat of ESTOL-C40B5-S or ESTOL-Adhesion Primer for thin layers without flank adhesion and concrete surfaces.
Distribute ESTOL-Biomak generously over the damaged area.
Sprinkle well with water (e.g. watering can); approx. 1 – 2l for 30 kg of mixture. Immediately compact the mix well using a tamper or agitator-plate.
Lightly sand the surface to decrease surface stickiness. Open section for flowing traffic. … finished!

ESTOL-Biomak is available in 30 kg containers. 27 containers are packed onto one pallet.
Store the container in a cool, dry place and do not expose to direct sunlight. ESTOL-Biomak can be stored in its unopened original container for up to 6 months. Partially empty containers must be used up quickly.
We are happy to send you a free, no-obligation quote and our technical data sheets. These data sheets will provide you with more data and information about how our products are processed.

ESTOL-Asphalt Cast

Quickly eliminates damage on any road surfaces with a depth of up to approx. 50 mm (fill and compact deeper damage using multiple layers of ESTOL-Asphalt Cast).
Lasting repair of damaged areas on surfaces exposed to heavy mechanical stress, like highways, main roads, race tracks, airports, industrial hangers (forklift traffic) etc. Filling drill holes
Creating new base surface layers after raising/regulating shafts, gutter connections, valve covers, etc. ramps

ESTOL-Asphalt Cast is a non-porous, thermo-plastic asphalt with grain size 0/4
– Ready-to-use in the form of a granulated product packed in a container
– Weather-safe, can be applied all year round
– Easy and fast repair solution on almost all surfaces
– Flows at processing temperatures of approx. 200 °C
– Can be exposed to heavy mechanical stress 10-20 min. after installation (depending on paving thickness)
– Stability is equal to a mastic asphalt surface
– Absolutely resistant to deformation
– Even at high temperatures in the summer months, no deformation is possible after setting.
– Can be paved over immediately with all standard hot mix coatings
– Complies with German regulations. ESTOL-Asphalt Cast is CE-certified

All loose particles, like dust, sand, etc. are to be removed from the surface being treated. In order to bind the dust, the surfaces should be treated with a thin coat of ESTOL-Adhesive or ESTOL-Adhesion Primer, especially where there is no flank adhesion and on concrete surfaces Heat ESTOL-Asphalt Cast in a suitable boiler while stirring regularly to at least 160 °C (for installation followed by re-compaction), or heat ESTOL-Asphalt Cast to at least 200 °C for the material to flow (no re-compaction required). Apply the material onto the surface and distribute using an appropriate tool (asphalt spreader, wooden spreader). The product can also be laid by hand layer-by-layer using a propane gas burner (heat evenly). If necessary, pre-bituminised, fine grained chippings can be scattered into the mixture while it is still hot, if the surface is meant to have more grip (lightly roll the chippings afterwards as needed). The area can be opened to traffic or other stress after approx. 10 – 20 min. depending on paving thickness.

12 kg plastic containers (packaged on euro-pallets 33 x 12 kg)
Big-Bag containing 0.95 t each
Store in a cool, dry place
Avoid lengthy exposure of the container to direct sunlight or heat
Unlimited storage period
We are happy to send you a free, no-obligation quote as well as our technical data sheets. These data sheets will provide you with more data and information about how our products are processed.